Custom Shade Installation | Installation in 9 Easy Steps
09-Aug
Get the best custom shade installation in Tulsa. Keep control of the natural light entering your home by installing cellular blinds. With these easily available window treatments, you can change the atmosphere and appearance of a room from bright and cheerful to dimly lit and quiet in seconds.
Cellular shades, also known as honeycomb shades, consisting of two fused layers of pleated polyester fabric. These easy-to-install curtains are sold in dozens of sizes, colors, and styles in home improvement, sawmills, and design centers. We install wireless blinds that have no annoying pull cord. To raise or lower the curtain, simply grab the lower rail and slide it up or down. Remember, roller blinds aren’t just for windows. they can also be installed on French doors. Pulp panels are cut to size so be careful when measuring and writing down your window dimensions.
Step 1: Window roller blind overview
To measure your windows for any shade, you first have to decide how you want to install them. There are two basic methods: indoor mounting and outdoor mounting. The inner bracket has a more finished look. To measure this installation, first determine the width by taking the distance between the two side posts. Measure at the top, bottom, and middle, using the smallest dimension. For length, measure from the bottom of the main post to the top of the stool (sole) on both sides and in the center of the window; use the smallest measurement again. Then double-check the measurements before ordering as all custom curtain sales are final.
Warning: Drawstring curtains can be a strangulation hazard for young children. Although most manufacturers use safety tabs and avoid cable loops, order cordless roller blinds for extra security.
Step 2: Mark bracket positions
Remove any existing sunshade and sunshade accessories that could interfere with the installation of the cellular sunshade.
Check the hardware that came with the display to make sure that all mounting brackets and screws are included.
Next, measure 2 inches in from each side post and make a mark on the main post above the window.
Step 3: Mark the locations of the screw holes
Hold one of the metal brackets against the main post and keep it aligned with the 2-inch pencil line.
To ensure that the bracket is square, align its leading edge with the leading edge of the main post.
While holding the bracket firmly in place, mark two mounting holes with a hole punch.
Repeat this process for the other media.
Step 4: Drill pilot holes
Use a drill bit with a 1/16-inch bit to drill pilot holes at each screw location. Keep the drill perfectly straight while drilling the main post.
If you are drilling into a stone or concrete lintel, use a 1/4 in. Diameter masonry drill bit and insert a lead dowel into each hole.
Vacuum up any sawdust you’ve created.
Tip: Install a third center bracket for windows over 44 inches wide. Get the best custom shade installation in Tulsa.
Step 5: Install the Mounting Brackets
Hold the bracket in place, making sure that it lines up with the pilot holes of the drilled screws in the main post.
Secure the bracket with two flat head screws.
Install the remaining mounting brackets.
Tip : If necessary, install extension brackets to secure the blind against obstacles, such as B. a window handle to slide past.
Step 6: Checking Brackets for Leveling
Hold a level between the two mounting brackets to see if they are level.
If your level isn’t long enough to get from one support to the other, cut a straight board to fit in the opening.
Hold the dashboard firmly by the two brackets, then place the spirit level on the lower edge of the dashboard and check for bubbles. Get the best custom shade installation in Tulsa.
Step 7: Insert a thin wooden wedge
If the brackets are 1/8 inch or less off the plane, go to step 7. If the gap is greater, loosen the “upper” bracket screws.
Slide a wooden wedge or thin pieces of cardboard between the bracket and the main post.
Tighten the screws and recheck the height of the brackets.
Repeat if necessary, then cut off the excess washer with a craft knife.
Step 8: Install the Display in the Brackets
Loosen the small screws called reinforcement screws on the underside of the brackets.
Next, lift the shade to the lintel post and hook the front edge of the curtain rail onto the protruding edge of the two brackets. Get the best custom shade installation in Tulsa.
Rotate the back of the headrail toward the window and tighten the clamp screws to secure the blind to the brackets.
Tip: When tightening the clamping screws, make sure that the fabric does not get caught in the holder.
Step 9: Test the function of the roller shutter
Check with the fastening screws firmly tightened whether the roller shutter is working properly.
Grasp the center of the lower rail and slowly pull down to extend the blind onto the stool or window sill.
Push up again with your hand in the middle of the railing to raise the blind, stop at various points along the way to check that the blind stays. Get the best custom shade installation in Tulsa.